华为数通---配置Smart Link负载分担案例

定义

Smart Link，又叫做备份链路。一个Smart Link由两个接口组成，其中一个接口作为另一个的备份。Smart Link常用于双上行组网，提供可靠高效的备份和快速的切换机制。?

目的

下游设备连接到上游设备，当使用单上行方式时，若出现单点故障，会造成业务中断。若采用双上行方式，将一台下游设备同时连接到两台上游设备，可降低单点故障对网络的影响，提高了可靠性。

组网需求

如下图所示，为了保证网络的可靠性，用户侧网络采用双上行方式组网。由于组网上存在多个VLAN的数据流量，为使链路得到充分利用，用户希望两条上行链路均进行数据流量的转发。组网要求业务中断时间控制在毫秒级。?

?

配置思路?

?采用如下的思路配置Smart Link功能：

• 在SwitchA上进行配置，将需要进行负载分担的VLAN 500映射到实例10。
• 在SwitchA上配置Smart Link组，将对应接口加入Smart Link组中。
• 在SwitchA上配置负载分担功能，实例10映射的VLAN数据从备份链路进行转发。
• 在SwitchA上使能回切功能，使得故障恢复后，流量切换到相对稳定的原主链路上。
• 在SwitchA上使能发送Flush报文功能。
• 在SwitchB、SwitchC和SwitchD三台设备对应接口上使能Flush报文接收功能。
• 在SwitchA上使能Smart Link组功能。

操作步骤?

（1）配置VLAN信息

# 在SwitchA上创建VLAN，并配置接口允许相应VLAN通过。SwitchB、SwitchC和SwitchD的配置与SwitchA相似，详见配置文件。

<Huawei>system-view 
[Huawei]sysname SwitchA
[SwitchA]vlan batch 10 100 500
[SwitchA]interface GigabitEthernet 0/0/1
[SwitchA-GigabitEthernet0/0/1]port link-type trunk 
[SwitchA-GigabitEthernet0/0/1]port trunk allow-pass vlan 10 100 500
[SwitchA-GigabitEthernet0/0/1]quit
[SwitchA]interface GigabitEthernet 0/0/2
[SwitchA-GigabitEthernet0/0/2]port link-type trunk 
[SwitchA-GigabitEthernet0/0/2]port trunk allow-pass vlan 10 100 500
[SwitchA-GigabitEthernet0/0/2]quit

（2）在SwitchA上配置VLAN映射

[SwitchA]stp region-configuration 
[SwitchA-mst-region]instance 10 vlan 500
[SwitchA-mst-region]active region-configuration 
[SwitchA-mst-region]quit

（3）将去使能STP功能的上行接口加入Smart Link组并指定为主接口或从接口

# 配置SwitchA

[SwitchA]interface GigabitEthernet 0/0/1	
[SwitchA-GigabitEthernet0/0/1]stp disable 
[SwitchA-GigabitEthernet0/0/1]quit
[SwitchA]interface GigabitEthernet 0/0/2	
[SwitchA-GigabitEthernet0/0/2]stp disable 
[SwitchA-GigabitEthernet0/0/2]quit
[SwitchA]smart-link group 1
[SwitchA-smlk-group1]port GigabitEthernet 0/0/1 master
[SwitchA-smlk-group1]port GigabitEthernet 0/0/2 slave 

（4）在SwitchA上配置负载分担功能

[SwitchA-smlk-group1]load-balance instance 10 slave

（5）使能回切功能并设置回切时间

# 配置SwitchA。

[SwitchA-smlk-group1]restore enable 
[SwitchA-smlk-group1]timer wtr 30

（6）使能发送Flush报文功能

# 配置SwitchA，并指定发送Flush报文的密码为SHA加密方式。

[SwitchA-smlk-group1]flush send control-vlan 10 password simple huawei-123

（7）使能接收Flush报文功能

# 配置SwitchB，并指定接收Flush报文的密码为SHA加密方式。

[SwitchB]interface GigabitEthernet 0/0/1
[SwitchB-GigabitEthernet0/0/1]smart-link flush receive control-vlan 10 password 
simple huawei-123
[SwitchB-GigabitEthernet0/0/1]stp disable 
[SwitchB-GigabitEthernet0/0/1]quit
[SwitchB]interface GigabitEthernet 0/0/2
[SwitchB-GigabitEthernet0/0/2]smart-link flush receive control-vlan 10 password 
simple huawei-123
[SwitchB-GigabitEthernet0/0/2]stp disable 
[SwitchB-GigabitEthernet0/0/2]quit

?# 配置SwitchC，并指定接收Flush报文的密码为SHA加密方式。

[SwitchC]interface GigabitEthernet 0/0/1
[SwitchC-GigabitEthernet0/0/1]smart-link flush receive control-vlan 10 password 
simple huawei-123
[SwitchC-GigabitEthernet0/0/1]stp disable 
[SwitchC-GigabitEthernet0/0/1]quit
[SwitchC]interface GigabitEthernet 0/0/2
[SwitchC-GigabitEthernet0/0/2]smart-link flush receive control-vlan 10 password 
simple huawei-123	
[SwitchC-GigabitEthernet0/0/2]stp disable 
[SwitchC-GigabitEthernet0/0/2]quit

?# 配置SwitchD，并指定接收Flush报文的密码为SHA加密方式。

[SwitchD]interface GigabitEthernet 0/0/1
[SwitchD-GigabitEthernet0/0/1]smart-link flush receive control-vlan 10 password 
simple huawei-123
[SwitchD-GigabitEthernet0/0/1]stp disable 
[SwitchD-GigabitEthernet0/0/1]quit
[SwitchD]interface GigabitEthernet 0/0/2
[SwitchD-GigabitEthernet0/0/2]smart-link flush receive control-vlan 10 password 
simple huawei-123
[SwitchD-GigabitEthernet0/0/2]stp disable 
[SwitchD-GigabitEthernet0/0/2]quit

（8）在SwitchA使能Smart Link组功能

[SwitchA-smlk-group1]smart-link enable
[SwitchA-smlk-group1]quit

（9）验证配置结果

# 使用display smart-link group命令查看SwitchA上的Smart Link组信息。如果显示如下信息，则表示配置成功。

• Smart Link组功能已经使能
• 回切时间为30秒
• 控制VLAN编号为10
• 接口GE0/0/1为主接口且处于Active状态，接口GE0/0/2为从接口且处于Inactive，并且配置了负载分担功能。

[SwitchA]display smart-link group 1
Smart Link group 1 information :
  Smart Link group was enabled
  Wtr-time is: 30 sec.
  Load-Balance Instance: 10 
  There is no protected-vlan reference-instance
  DeviceID: 4c1f-cc8e-66bb  Control-vlan ID: 10
  Member                  Role   State    Flush Count Last-Flush-Time
  ----------------------------------------------------------------------

  GigabitEthernet0/0/1    Master Active   1           2023/12/07 15:57:28 UTC-08
:00 
  GigabitEthernet0/0/2    Slave  Inactive 0           0000/00/00 00:00:00 UTC+00
:00 

?# 使用shutdown命令关闭接口GE0/0/1，可以看到接口GE0/0/1已经处于Inactive状态，接口GE0/0/2为Active状态。

[SwitchA]interface GigabitEthernet 0/0/1
[SwitchA-GigabitEthernet0/0/1]shutdown
[SwitchA-GigabitEthernet0/0/1]display smart-link group 1
Smart Link group 1 information :
  Smart Link group was enabled
  Wtr-time is: 30 sec.
  Load-Balance Instance: 10 
  There is no protected-vlan reference-instance
  DeviceID: 4c1f-cc8e-66bb  Control-vlan ID: 10
  Member                  Role   State    Flush Count Last-Flush-Time
  ----------------------------------------------------------------------

  GigabitEthernet0/0/1    Master Inactive 1           2023/12/07 15:57:28 UTC-08
:00 
  GigabitEthernet0/0/2    Slave  Active   0           0000/00/00 00:00:00 UTC+00
:00 

?# 使用undo shutdown命令开启接口GE0/0/1。

[SwitchA-GigabitEthernet0/0/1]undo shutdown

?# 等待30秒后，可以看到接口GE0/0/1处于Active状态，接口GE0/0/2为Inactive状态。

[SwitchA-GigabitEthernet0/0/1]display smart-link group 1
Smart Link group 1 information :
  Smart Link group was enabled
  Wtr-time is: 30 sec.
  Load-Balance Instance: 10 
  There is no protected-vlan reference-instance
  DeviceID: 4c1f-cc8e-66bb  Control-vlan ID: 10
  Member                  Role   State    Flush Count Last-Flush-Time
  ----------------------------------------------------------------------

  GigabitEthernet0/0/1    Master Active   2           2023/12/07 16:03:41 UTC-08
:00 
  GigabitEthernet0/0/2    Slave  Inactive 0           0000/00/00 00:00:00 UTC+00
:00 

?# 假设PC1所属的VLAN为VLAN100，PC2所属的VLAN为VLAN500，PC1和PC2都能访问Internet。

配置文件?

• SwitchA的配置文件

#
sysname SwitchA
#
vlan batch 10 100 500
#
stp region-configuration
 instance 10 vlan 500
 active region-configuration
#
interface GigabitEthernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 10 100 500
 stp disable
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 10 100 500
 stp disable
#
smart-link group 1
 load-balance instance 10 slave
 restore enable
 smart-link enable
 port GigabitEthernet0/0/1 master
 port GigabitEthernet0/0/2 slave
 timer wtr 30
 flush send control-vlan 10 password simple huawei-123
#
return

• SwitchB的配置文件

#
sysname SwitchB
#
vlan batch 10 100 500
#
interface GigabitEthernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 10 100 500
 stp disable
 smart-link flush receive control-vlan 10 password simple huawei-123
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 10 100 500
 stp disable
 smart-link flush receive control-vlan 10 password simple huawei-123
return

• SwitchC的配置文件

#
sysname SwitchC
#
vlan batch 10 100 500
#
interface GigabitEthernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 10 100 500
 stp disable
 smart-link flush receive control-vlan 10 password simple huawei-123
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 10 100 500
 stp disable
 smart-link flush receive control-vlan 10 password simple huawei-123
#
return

• SwitchD的配置文件

#
sysname SwitchD
#
vlan batch 10 100 500
#
interface GigabitEthernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 10 100 500
 stp disable
 smart-link flush receive control-vlan 10 password simple huawei-123
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 10 100 500
 stp disable
 smart-link flush receive control-vlan 10 password simple huawei-123
#
return