linux查看网卡是100M还是1000M

可以使用?ethtool?命令进行查看，使用格式：ethtool 网络接口名

以下为例，使用?ifconfig?查看当前使用的网卡，获取网卡名字：enp2s0

root@U-NAS:~# ifconfig
enp2s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.8  netmask 255.255.255.0  broadcast 192.168.0.255
        inet6 fe80::2e0:70ff:fe86:cf8c  prefixlen 64  scopeid 0x20<link>
        ether 00:e0:70:86:cf:8c  txqueuelen 1000  (Ethernet)
        RX packets 403272  bytes 400480688 (381.9 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 352875  bytes 233242041 (222.4 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1  (Local Loopback)
        RX packets 1250  bytes 11161999 (10.6 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1250  bytes 11161999 (10.6 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

root@U-NAS:~#

使用?ethtool enp2s0?命令进行查看

root@U-NAS:~# ethtool enp2s0
Settings for enp2s0:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supported pause frame use: No
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00000033 (51)
                               drv probe ifdown ifup
        Link detected: yes
root@U-NAS:~#

Speed?表示网卡带宽，Duplex?表示工作模式，Supported link modes?表示支持的工作模式。

扩展资料：

ethtool命令的其它用法：

Ps:以下示例，网卡名为eth0

1、查询网络端口位置：ethtool -p ethX

这个命令多用于管理多网口的服务器主机，由于背板的网络端口数量大，有时候不知道那个物理端口对应eth0或其他设备号，我们就可以使用这个命令来查询。

用法：ethtool -p eth0

效果：设备号eth0对应的物理端口的两个指示灯会闪烁

2、修改网络端口速率：ethtool -s

这个命令多用于手工设置网络速率，一般千兆网卡支持10|100|1000三个速率，单位是Mbps。

用法：ethtool -s eth0 speed 1000 duplex full autoneg off

效果：将设备号eth0对应的物理端口设置为速率为1000Mbps，全双工工作模式，同时关闭自动协商。