21、Kubernetes核心技术 - 高可用集群搭建（kubeadm+keepalived+haproxy）
2024-01-09 16:05:42
目录
(6)、所有节点安装kubeadm，kubelet和kubectl
(11-2)、k8s-node-01、k8s-node-02 加入集群
一、简介
前面我们介绍了使用kubeadm搭建k8s集群，当时只使用了一个master节点，其实是不满足k8s高可用的。因为当master节点发生宕机时，通过node节点将无法继续访问，所以整个集群将无法正常提供服务。
本篇文章，我们将使用kubeadm，配合keepalived、haproxy来实现k8s集群的高可用。
二、高可用集群架构说明
k8s集群的高可用主要体现在master相关组件及etcd，master中apiserver是集群的入口，搭建三个master通过keepalived提供一个vip（虚拟IP）实现高可用，并且添加haproxy来为apiserver提供反向代理的作用，这样来自haproxy的所有请求都将轮询转发到后端的master节点上。如果仅仅使用keepalived，当集群正常工作时，所有的流量还是会转发到具有vip（虚拟IP）的那台master上面，因此加上了haproxy使整个集群的master都能参与进来，集群的健壮性更强。
对应架构图如下所示：
简单来说，就是需要满足下面两个条件：
- 1)、在 node 节点和 master 节点之间，需要一个 LoadBalancer 组件
-
- 【作用 1】负载均衡
- 【作用 2】检查 master 节点的状态
- 2)、对外需要一个统一的 VIP（虚拟IP）
-
- 【作用 1】虚拟 ip 对外进行访问
三、部署环境说明
由于这里使用虚拟机搭建，资源有限，我们采用 2 个 master 节点，2个 node 节点来搭建高可用k8s集群。文中使用到的服务器ip及角色对应如下。
| 主机名称 | ip地址 | 角色 |
| k8s-vip | 192.168.1.39 | 虚拟ip(vip) |
| k8s-master-01 | 192.168.1.35 | master |
| k8s-master-02 | 192.168.1.36 | master |
| k8s-node-01 | 192.168.1.37 | node |
| K8s-node-02 | 192.168.1.38 | node |
四、高可用集群搭建
(1)、初始化所有节点
所有节点，需关闭防火墙规则，关闭selinux，关闭swap交换、时间同步。
[root@localhost ~]# systemctl stop firewalld
[root@localhost ~]# systemctl disable firewalld
[root@localhost ~]# setenforce 0
[root@localhost ~]# sed -i 's/SELINUX=enforcing/\SELINUX=disabled/' /etc/selinux/config
# 禁用swap, kubeadm会检查当前主机是否禁用了swap，如果启动了swap将导致安装不能正常进行，所以需要禁用所有的swap
[root@localhost ~]# swapoff -a
[root@localhost ~]# sed -ri 's/.*swap.*/#&/' /etc/fstab
[root@localhost ~]# free -g
total used free shared buff/cache available
Mem: 7 5 1 0 0 2
Swap: 0 0 0
# 最后执行时间同步
[root@localhost ~]# yum install ntpdate -y
[root@localhost ~]# ntpdate time.windows.com以k8s-master-01为例，在k8s-master-02、k8s-node-01、k8s-node-02也需要执行。
(2)、修改host文件
根据规划设置主机名分别修改每台服务器的hostname主机名称：
# 根据规划设置主机名【k8s-master-01 节点上操作】
hostnamectl set-hostname k8s-master-01
# 根据规划设置主机名【k8s-master-02 节点上操作】
hostnamectl set-hostname k8s-master-02
# 根据规划设置主机名【k8s-node-01 节点操作】
hostnamectl set-hostname k8s-node-01
# 根据规划设置主机名【k8s-node-02 节点操作】
hostnamectl set-hostname k8s-node-02然后将上面的内容复制到host文件中，所有节点修改主机名和hosts文件，文件内容如下：
cat >> /etc/hosts << EOF
192.168.1.39 master.k8s.io k8s-vip
192.168.1.35 master01.k8s.io k8s-master-01
192.168.1.36 master02.k8s.io k8s-master-02
192.168.1.37 node01.k8s.io k8s-node-01
192.168.1.38 node02.k8s.io k8s-node-02
EOF以k8s-master-01为例，在k8s-master-02、k8s-node-01、k8s-node-02也需要执行，注意主机名称不一样。
(3)、调整内核参数
将桥接的 IPV4 流量传递到 iptables 链。
cat > /etc/sysctl.d/k8s.conf << EOF
net.bridge.bridge-nf-call-ip6tables = 1
net.bridge.bridge-nf-call-iptables = 1
EOF以k8s-master-01为例，在k8s-master-02、k8s-node-01、k8s-node-02也需要执行。
修改完成后，在所有节点执行sysctl --system加载参数使其生效：
(4)、所有节点安装Docker
所有节点安装 docker/kubelet/kubeadm/kubectl，Kubernetes 默认 CRI（容器运行时）为 docker，因此先安装 docker，以k8s-master-01为例，在k8s-master-02、k8s-node-01、k8s-node-02也需要执行。
(4-1)、配置 docker 的阿里 yum 源?
cat >/etc/yum.repos.d/docker.repo<<EOF
[docker-ce-edge]
name=Docker CE Edge - $basearch
baseurl=https://mirrors.aliyun.com/docker-ce/linux/centos/7/$basearch/edge
enabled=1
gpgcheck=1
gpgkey=https://mirrors.aliyun.com/docker-ce/linux/centos/gpg
EOF(4-2)、yum 安装 docker?
# yum 安装
yum -y install docker-ce
# 查看 docker 版本
docker --version ?(4-3)、配置 docker 的镜像源
cat >> /etc/docker/daemon.json << EOF
{
"registry-mirrors": ["https://b9pmyelo.mirror.aliyuncs.com"]
}
EOF(4-4)、启动 docker?
systemctl start docker
systemctl enable docker
systemctl status docker
(5)、所有节点配置K8S源
执行下面的命令，定义kubernetes源：
cat > /etc/yum.repos.d/kubernetes.repo << EOF
[kubernetes]
name=Kubernetes
baseurl=https://mirrors.aliyun.com/kubernetes/yum/repos/kubernetes-el7-x86_64
enabled=1
gpgcheck=0
repo_gpgcheck=0
gpgkey=https://mirrors.aliyun.com/kubernetes/yum/doc/yum-key.gpg https://mirrors.aliyun.com/kubernetes/yum/doc/rpm-package-key.gpg
EOF以k8s-master-01为例，在k8s-master-02、k8s-node-01、k8s-node-02也需要执行：
(6)、所有节点安装kubeadm，kubelet和kubectl
由于版本更新频繁，这里指定版本号1.21.3部署。?
[root@localhost ~]# yum install -y kubelet-1.21.3 kubeadm-1.21.3 kubectl-1.21.3以k8s-master-01为例，在k8s-master-02、k8s-node-01、k8s-node-02也需要执行：
这里根据网速快慢，可能需等待一些时间。
安装完毕之后，如下图。
k8s通过kubeadm安装出来以后都是以Pod方式存在，即底层是以容器方式运行，所以kubelet必须设置开机自启。
systemctl enable kubelet(7)、所有master 节点安装keepalived
【k8s-master-01 + k8s-master-02上操作】
(7-1)、安装keepalived?
yum install -y keepalived(7-2)、配置keepalived
keepalived中使用track_script机制来配置脚本进行探测kubernetes的master节点是否宕机，并以此切换节点实现高可用。
k8s-master-01节点的keepalived配置文件如下所示，配置文件所在的位/etc/keepalived/keepalived.cfg：
cat > /etc/keepalived/keepalived.conf <<EOF
! Configuration File for keepalived
global_defs {
router_id k8s
}
vrrp_script check_haproxy {
script "killall -0 haproxy"
interval 3
weight -2
fall 10
rise 2
}
vrrp_instance VI_1 {
state MASTER
interface ens33
mcast_src_ip 192.168.1.35
virtual_router_id 51
priority 100
advert_int 1
authentication {
auth_type PASS
auth_pass ceb1b3ec013d66163d6ab
}
virtual_ipaddress {
192.168.1.39
}
track_script {
check_haproxy
}
}
EOF需要注意几点：
- mcast_src_ip：配置多播源地址，此地址是当前主机的 ip 地址。
- priority：keepalived根据此项参数的大小仲裁master节点。我们这里让 master 节点为kubernetes提供服务，其他两个节点暂时为备用节点。因此k8s-master-01节点设置为100，k8s-master-02节点设置为99。
- state：我们将k8s-master-01节点的state字段设置为MASTER，其他节点字段修改为BACKUP。
配置 k8s-master-02 节点，配置文件内容如下：
cat > /etc/keepalived/keepalived.conf <<EOF
! Configuration File for keepalived
global_defs {
router_id k8s
}
vrrp_script check_haproxy {
script "killall -0 haproxy"
interval 3
weight -2
fall 10
rise 2
}
vrrp_instance VI_1 {
state BACKUP
interface ens33
mcast_src_ip 192.168.1.36
virtual_router_id 51
priority 99
advert_int 1
authentication {
auth_type PASS
auth_pass ceb1b3ec013d66163d6ab
}
virtual_ipaddress {
192.168.1.39
}
track_script {
check_haproxy
}
}
EOF
(7-3)、启动、检查keepalived
【k8s-master-01 和 k8s-master-02 均要启动】?
# 设置开机启动
systemctl enable keepalived.service
# 启动keepalived
systemctl start keepalived.service
# 查看启动状态
systemctl status keepalived.service
启动成功后，我们通过下面的命令查看 master 网卡信息：
ip a s ens33
可以看到，当前虚拟IP（192.168.1.39）是飘移到了k8s-master-01这个节点。我们可以尝试停掉k8s-master-01的keepalived服务，查看vip是否能漂移到其他的master，并且重新启动k8s-master-01的keepalived服务，查看vip是否能正常漂移回来，证明配置没有问题。
(8)、所有master 节点安装haproxy
【k8s-master-01 + k8s-master-02上操作】
(8-1)、安装haproxy?
yum install -y haproxy(8-2)、配置haproxy
所有master节点的haproxy配置相同，haproxy 的配置文件是/etc/haproxy/haproxy.cfg。
配置中声明了后端代理的两个 master 节点服务器，指定了 haproxy 运行的端口为 16443 等，因此 16443 端口为集群的入口。
cat > /etc/haproxy/haproxy.cfg << EOF
#---------------------------------------------------------------------
# Global settings
#---------------------------------------------------------------------
global
# to have these messages end up in /var/log/haproxy.log you will
# need to:
# 1) configure syslog to accept network log events. This is done
# by adding the '-r' option to the SYSLOGD_OPTIONS in
# /etc/sysconfig/syslog
# 2) configure local2 events to go to the /var/log/haproxy.log
# file. A line like the following can be added to
# /etc/sysconfig/syslog
#
# local2.* /var/log/haproxy.log
#
log 127.0.0.1 local2
chroot /var/lib/haproxy
pidfile /var/run/haproxy.pid
maxconn 4000
user haproxy
group haproxy
daemon
# turn on stats unix socket
stats socket /var/lib/haproxy/stats
#---------------------------------------------------------------------
# common defaults that all the 'listen' and 'backend' sections will
# use if not designated in their block
#---------------------------------------------------------------------
defaults
mode http
log global
option httplog
option dontlognull
option http-server-close
option forwardfor except 127.0.0.0/8
option redispatch
retries 3
timeout http-request 10s
timeout queue 1m
timeout connect 10s
timeout client 1m
timeout server 1m
timeout http-keep-alive 10s
timeout check 10s
maxconn 3000
#---------------------------------------------------------------------
# kubernetes apiserver frontend which proxys to the backends
#---------------------------------------------------------------------
frontend kubernetes-apiserver
mode tcp
bind *:16443
option tcplog
default_backend kubernetes-apiserver
#---------------------------------------------------------------------
# round robin balancing between the various backends
#---------------------------------------------------------------------
backend kubernetes-apiserver
mode tcp
balance roundrobin
server k8s-master-01 192.168.1.35:6443 check
server k8s-master-02 192.168.1.36:6443 check
#---------------------------------------------------------------------
# collection haproxy statistics message
#---------------------------------------------------------------------
listen stats
bind *:10080
stats auth admin:awesomePassword
stats refresh 5s
stats realm HAProxy\ Statistics
stats uri /admin?stats
EOF
(8-3)、启动和检查haproxy
# 设置开机启动
systemctl enable haproxy
# 开启haproxy
systemctl start haproxy
# 查看启动状态
systemctl status haproxy
# 检查端口
netstat -lntup | grep haproxy
(9)、安装、初始化master
在具有vip的master上操作，这里为k8s-master-01这个节点。
(9-1)、创建kubeadm配置文件
[root@k8s-master-01]# vim kubeadm-config.yaml
apiServer:
certSANs:
- k8s-master-01
- k8s-master-02
- k8s-master-03
- master.k8s.io
- 192.168.1.35
- 192.168.1.36
- 192.168.1.39
- 127.0.0.1
extraArgs:
authorization-mode: Node,RBAC
timeoutForControlPlane: 4m0s
apiVersion: kubeadm.k8s.io/v1beta2
certificatesDir: /etc/kubernetes/pki
clusterName: kubernetes
controlPlaneEndpoint: "master.k8s.io:16443"
controllerManager: {}
dns:
type: CoreDNS
etcd:
local:
dataDir: /var/lib/etcd
imageRepository: registry.aliyuncs.com/google_containers
kind: ClusterConfiguration
kubernetesVersion: v1.21.3
networking:
dnsDomain: cluster.local
podSubnet: 10.244.0.0/16
serviceSubnet: 10.1.0.0/16
scheduler: {}(9-2)、初始化master节点??
[root@k8s-master-01]# kubeadm init --config kubeadm-config.yaml
执行kubeadm init 初始化，中间会拉取镜像，速度较慢。执行完后，如下图，我们需要提前复制一下下图框起来的几个命令：
(9-3)、按照提示配置环境变量??
[root@k8s-master-01]# mkdir -p $HOME/.kube
[root@k8s-master-01]# sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config
[root@k8s-master-01]# sudo chown $(id -u):$(id -g) $HOME/.kube/config(9-4)、查看集群状态?
[root@k8s-master-01 ~]# kubectl get cs
Warning: v1 ComponentStatus is deprecated in v1.19+
NAME STATUS MESSAGE ERROR
scheduler Unhealthy Get "http://127.0.0.1:10251/healthz": dial tcp 127.0.0.1:10251: connect: connection refused
controller-manager Unhealthy Get "http://127.0.0.1:10252/healthz": dial tcp 127.0.0.1:10252: connect: connection refused
etcd-0 Healthy {"health":"true"} 可以看到，scheduler和controller-manager的状态都是Unhealthy，我们需要修改配置文件：
- vim /etc/kubernetes/manifests/kube-scheduler.yaml
将- --port=0注释掉。
- vim /etc/kubernetes/manifests/kube-controller-manager.yaml
将- --port=0注释掉。
修改完成后，继续查看master状态：?
[root@k8s-master-01 ~]# kubectl get cs
Warning: v1 ComponentStatus is deprecated in v1.19+
NAME STATUS MESSAGE ERROR
controller-manager Healthy ok
scheduler Healthy ok
etcd-0 Healthy {"health":"true"} 可以看到， 各个组件的状态都是Healthy健康状态。
查看集群pod：?
[root@k8s-master-01 ~]# kubectl get pods -n kube-system
NAME READY STATUS RESTARTS AGE
coredns-59d64cd4d4-jw4s4 0/1 Pending 0 10m
coredns-59d64cd4d4-zp7kk 0/1 Pending 0 10m
etcd-k8s-master-01 1/1 Running 0 10m
kube-apiserver-k8s-master-01 1/1 Running 0 10m
kube-controller-manager-k8s-master-01 1/1 Running 0 65s
kube-proxy-d6vkg 1/1 Running 0 10m
kube-scheduler-k8s-master-01 1/1 Running 0 85s
[root@k8s-master-01 ~]# kubectl get nodes -n kube-system
NAME STATUS ROLES AGE VERSION
k8s-master-01 NotReady control-plane,master 14m v1.21.3如上，集群默认也把coredns安装了，这里处于pending状态的原因是因为还没有安装集群网络组件。
(10)、安装集群网络组件
【 k8s-master-01上操作】
先从GitHub仓库下载kube-flannel.yml：?
kubectl apply -f https://raw.githubusercontent.com/coreos/flannel/master/Documentation/kube-flannel.yml国外站点下载很慢，经常连不上：
安装：?
kubectl apply -f http://120.78.77.38/file/kube-flannel.yaml安装完CNI网络插件后，节点的状态就变成Ready了。我们使用查看pod状态，可以看到，状态都是Running运行状态。
[root@k8s-master-01 ~]# kubectl get pod -n kube-system
NAME READY STATUS RESTARTS AGE
coredns-59d64cd4d4-jw4s4 1/1 Running 0 24m
coredns-59d64cd4d4-zp7kk 1/1 Running 0 24m
etcd-k8s-master-01 1/1 Running 0 24m
kube-apiserver-k8s-master-01 1/1 Running 0 24m
kube-controller-manager-k8s-master-01 1/1 Running 0 14m
kube-flannel-ds-amd64-cf9k2 1/1 Running 0 8m
kube-proxy-d6vkg 1/1 Running 0 24m
kube-scheduler-k8s-master-01 1/1 Running 0 15m
[root@k8s-master-01 ~]# kubectl get node -n kube-system
NAME STATUS ROLES AGE VERSION
k8s-master-01 Ready control-plane,master 24m v1.21.3?(11)、其他节点加入集群
【 k8s-master-02 + k8s-node-01 + k8s-node-02上操作】
(11-1)、k8s-master-02加入集群
(11-1-1)、复制密钥及相关文件
在第一次执行init的机器，此处为k8s-master-01上操作，复制文件到k8s-master-02。
ssh root@192.168.1.36 mkdir -p /etc/kubernetes/pki/etcd
scp /etc/kubernetes/admin.conf root@192.168.1.36:/etc/kubernetes
scp /etc/kubernetes/pki/{ca.*,sa.*,front-proxy-ca.*} root@192.168.1.36:/etc/kubernetes/pki
scp /etc/kubernetes/pki/etcd/ca.* root@192.168.1.36:/etc/kubernetes/pki/etcd
(11-1-2)、master加入集群
在k8s-master-02上操作，执行在k8s-master-01上init后输出的join命令：
kubeadm join master.k8s.io:16443 --token f8iwdm.1hhk6zo1onlre1qi \
--discovery-token-ca-cert-hash sha256:57d56607b336b9ed62f07ac9eabdda5c90215b6cf251d2af3b98c82b1ea4fe66 \
--control-plane在k8s-master-02上执行join命令，需要带上参数--control-plane表示把master控制节点加入集群。
[root@k8s-master-02 /]# kubeadm join master.k8s.io:16443 --token f8iwdm.1hhk6zo1onlre1qi \
> --discovery-token-ca-cert-hash sha256:57d56607b336b9ed62f07ac9eabdda5c90215b6cf251d2af3b98c82b1ea4fe66 \
> --control-plane
[preflight] Running pre-flight checks
[WARNING IsDockerSystemdCheck]: detected "cgroupfs" as the Docker cgroup driver. The recommended driver is "systemd". Please follow the guide at https://kubernetes.io/docs/setup/cri/
[preflight] Reading configuration from the cluster...
[preflight] FYI: You can look at this config file with 'kubectl -n kube-system get cm kubeadm-config -o yaml'
[preflight] Running pre-flight checks before initializing the new control plane instance
[preflight] Pulling images required for setting up a Kubernetes cluster
[preflight] This might take a minute or two, depending on the speed of your internet connection
[preflight] You can also perform this action in beforehand using 'kubeadm config images pull'
[certs] Using certificateDir folder "/etc/kubernetes/pki"
[certs] Generating "apiserver" certificate and key
[certs] apiserver serving cert is signed for DNS names [k8s-master-01 k8s-master-02 k8s-master-03 kubernetes kubernetes.default kubernetes.default.svc kubernetes.default.svc.cluster.local master.k8s.io] and IPs [10.1.0.1 192.168.1.36 192.168.1.35 192.168.1.39 127.0.0.1]
[certs] Generating "apiserver-kubelet-client" certificate and key
[certs] Generating "front-proxy-client" certificate and key
[certs] Generating "etcd/healthcheck-client" certificate and key
[certs] Generating "apiserver-etcd-client" certificate and key
[certs] Generating "etcd/server" certificate and key
[certs] etcd/server serving cert is signed for DNS names [k8s-master-02 localhost] and IPs [192.168.1.36 127.0.0.1 ::1]
[certs] Generating "etcd/peer" certificate and key
[certs] etcd/peer serving cert is signed for DNS names [k8s-master-02 localhost] and IPs [192.168.1.36 127.0.0.1 ::1]
[certs] Valid certificates and keys now exist in "/etc/kubernetes/pki"
[certs] Using the existing "sa" key
[kubeconfig] Generating kubeconfig files
[kubeconfig] Using kubeconfig folder "/etc/kubernetes"
[endpoint] WARNING: port specified in controlPlaneEndpoint overrides bindPort in the controlplane address
[kubeconfig] Using existing kubeconfig file: "/etc/kubernetes/admin.conf"
[endpoint] WARNING: port specified in controlPlaneEndpoint overrides bindPort in the controlplane address
[kubeconfig] Writing "controller-manager.conf" kubeconfig file
[endpoint] WARNING: port specified in controlPlaneEndpoint overrides bindPort in the controlplane address
[kubeconfig] Writing "scheduler.conf" kubeconfig file
[control-plane] Using manifest folder "/etc/kubernetes/manifests"
[control-plane] Creating static Pod manifest for "kube-apiserver"
[control-plane] Creating static Pod manifest for "kube-controller-manager"
[control-plane] Creating static Pod manifest for "kube-scheduler"
[check-etcd] Checking that the etcd cluster is healthy
[kubelet-start] Writing kubelet configuration to file "/var/lib/kubelet/config.yaml"
[kubelet-start] Writing kubelet environment file with flags to file "/var/lib/kubelet/kubeadm-flags.env"
[kubelet-start] Starting the kubelet
[kubelet-start] Waiting for the kubelet to perform the TLS Bootstrap...
[etcd] Announced new etcd member joining to the existing etcd cluster
[etcd] Creating static Pod manifest for "etcd"
[etcd] Waiting for the new etcd member to join the cluster. This can take up to 40s
[upload-config] Storing the configuration used in ConfigMap "kubeadm-config" in the "kube-system" Namespace
[mark-control-plane] Marking the node k8s-master-02 as control-plane by adding the labels: [node-role.kubernetes.io/master(deprecated) node-role.kubernetes.io/control-plane node.kubernetes.io/exclude-from-external-load-balancers]
[mark-control-plane] Marking the node k8s-master-02 as control-plane by adding the taints [node-role.kubernetes.io/master:NoSchedule]
This node has joined the cluster and a new control plane instance was created:
* Certificate signing request was sent to apiserver and approval was received.
* The Kubelet was informed of the new secure connection details.
* Control plane (master) label and taint were applied to the new node.
* The Kubernetes control plane instances scaled up.
* A new etcd member was added to the local/stacked etcd cluster.
To start administering your cluster from this node, you need to run the following as a regular user:
mkdir -p $HOME/.kube
sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config
sudo chown $(id -u):$(id -g) $HOME/.kube/config
Run 'kubectl get nodes' to see this node join the cluster.
[root@k8s-master-02 /]# mkdir -p $HOME/.kube
[root@k8s-master-02 /]# sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config
[root@k8s-master-02 /]# sudo chown $(id -u):$(id -g) $HOME/.kube/config
(11-1-3)、检查集群及pod状态
在其中一台master上执行命令检查集群及pod状态。
[root@k8s-master-02 /]# kubectl get node
NAME STATUS ROLES AGE VERSION
k8s-master-01 Ready control-plane,master 34m v1.21.3
k8s-master-02 Ready control-plane,master 84s v1.21.3
[root@k8s-master-02 /]# kubectl get pods --all-namespaces
NAMESPACE NAME READY STATUS RESTARTS AGE
kube-system coredns-59d64cd4d4-jw4s4 1/1 Running 0 34m
kube-system coredns-59d64cd4d4-zp7kk 1/1 Running 0 34m
kube-system etcd-k8s-master-01 1/1 Running 0 34m
kube-system etcd-k8s-master-02 1/1 Running 0 87s
kube-system kube-apiserver-k8s-master-01 1/1 Running 0 34m
kube-system kube-apiserver-k8s-master-02 1/1 Running 0 85s
kube-system kube-controller-manager-k8s-master-01 1/1 Running 1 24m
kube-system kube-controller-manager-k8s-master-02 1/1 Running 0 81s
kube-system kube-flannel-ds-amd64-bm9gq 1/1 Running 0 93s
kube-system kube-flannel-ds-amd64-cf9k2 1/1 Running 0 17m
kube-system kube-proxy-d6vkg 1/1 Running 0 34m
kube-system kube-proxy-s548k 1/1 Running 0 93s
kube-system kube-scheduler-k8s-master-01 1/1 Running 1 24m
kube-system kube-scheduler-k8s-master-02 1/1 Running 0 70s如上，可以看到，当前集群中有两个node，并且状态都是Ready，并且pod状态也都是Running。
(11-2)、k8s-node-01、k8s-node-02 加入集群
(11-2-1)、node加入集群
在其他两台node节点上操作，执行join命令，在k8s-node-01和k8s-node-02上操作：?
?(11-2-2)、检查集群及pod状态
[root@k8s-master-02 /]# kubectl get node
NAME STATUS ROLES AGE VERSION
k8s-master-01 Ready control-plane,master 37m v1.21.3
k8s-master-02 Ready control-plane,master 4m58s v1.21.3
k8s-node-01 Ready <none> 60s v1.21.3
k8s-node-02 Ready <none> 56s v1.21.3
[root@k8s-master-01 ~]# kubectl get pods -n kube-system
NAME READY STATUS RESTARTS AGE
coredns-59d64cd4d4-jw4s4 1/1 Running 0 48m
coredns-59d64cd4d4-zp7kk 1/1 Running 0 48m
etcd-k8s-master-01 1/1 Running 0 48m
etcd-k8s-master-02 1/1 Running 0 16m
kube-apiserver-k8s-master-01 1/1 Running 0 48m
kube-apiserver-k8s-master-02 1/1 Running 0 16m
kube-controller-manager-k8s-master-01 1/1 Running 1 39m
kube-controller-manager-k8s-master-02 1/1 Running 0 16m
kube-flannel-ds-amd64-bm9gq 1/1 Running 0 16m
kube-flannel-ds-amd64-cf9k2 1/1 Running 0 32m
kube-flannel-ds-amd64-vz5z9 1/1 Running 0 12m
kube-flannel-ds-amd64-xwpg2 1/1 Running 0 12m
kube-proxy-5kzr8 1/1 Running 0 12m
kube-proxy-d6mfp 1/1 Running 0 12m
kube-proxy-d6vkg 1/1 Running 0 48m
kube-proxy-s548k 1/1 Running 0 16m
kube-scheduler-k8s-master-01 1/1 Running 1 39m
kube-scheduler-k8s-master-02 1/1 Running 0 15m如上，可以看到，当前集群中有四个node，并且状态都是Ready，并且pod状态也都是Running。
(12)、测试 kubernetes 集群
在 Kubernetes 集群中创建一个 pod，验证是否正常运行：?
# 创建 nginx deployment
[root@k8s-master-01 ~]# kubectl create deployment nginx --image=nginx
deployment.apps/nginx created
# 暴露端口
[root@k8s-master-01 ~]# kubectl expose deployment nginx --port=80 --type=NodePort
service/nginx exposed
# 查看状态
[root@k8s-master-01 ~]# kubectl get pod,svc
NAME READY STATUS RESTARTS AGE
pod/nginx-6799fc88d8-56nsc 0/1 ContainerCreating 0 14s
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
service/kubernetes ClusterIP 10.1.0.1 <none> 443/TCP 41m
service/nginx NodePort 10.1.196.129 <none> 80:30736/TCP 6s我们看到，对外暴露的端口号是30736，我们可以使用任意一台节点的IP加上端口号，访问：
192.168.1.35:30736
192.168.1.36:30736
192.168.1.37:30736
192.168.1.38:30736
192.168.1.39:30736
接下来，我们尝试停掉k8s-master-01（这里我直接将这台虚拟机关了），测试一下集群是否正常提供服务：
可以看到，虚拟IP（192.168.1.39）已经漂移到k8s-master-02节点上。浏览器再次访问：http://192.168.1.36:30736/、http://192.168.1.37:30736/、http://192.168.1.38:30736/、http://192.168.1.39:30736/，也能正常访问到nginx。
文章来源:https://blog.csdn.net/Weixiaohuai/article/details/135478349
本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。 如若内容造成侵权/违法违规/事实不符，请联系我的编程经验分享网邮箱：veading@qq.com进行投诉反馈，一经查实，立即删除！
本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。 如若内容造成侵权/违法违规/事实不符，请联系我的编程经验分享网邮箱：veading@qq.com进行投诉反馈，一经查实，立即删除！